Quality and safety resonate throughout all our management practices at Hercules SLR. Providing quality products and services with the highest standards in safety is integral to our operations and as such we are registered, accredited or members of the following professional organizations:
The Hercules SLR safety program is COR Certified in 3 provinces: Nova Scotia, Newfoundland and Alberta. Many large industrial companies such as ExxonMobil, Shell and Suncor have audited our program which includes orientation and training for every team member.
This comprehensive program contains work safe and standard operating procedures for all our major processes. Our technicians start every job by conducting a safety analysis (FLHA) and holding on-site tool box meetings to ensure everyone understands potential job hazards to minimize risks.[/accordion-item] [/accordion]
Hercules SLR is long time member of AWRF, a trade association that covers the spectrum of the lifting, rigging and load securement industry. AWRF members constantly strive to maintain the highest standards of quality and service obtainable in the industry. We are proud of our relationship with AWRF.[/accordion-item] [/accordion]
Download OurISO9001:2015 Certificate
All ratings shown on this web site meet or exceed ASME/ANSI 30.9 standards and are based upon the item being new or in “as new” condition. Ratings are considered to be the greatest load that should be applied to the item.
Ratings are based upon usual environmental conditions and consideration must be given to item selection when unusual conditions are to be encountered.
In general, the products displayed within this web site are used as part of a system being employed to accomplish a task. Therefore, we only recommend the utilization of such products to accomplish the desired task within the Working Load Limit (WLL).
The products shown are subject to wear, misuse, overloading, corrosion, deformation, intentional alteration and other usage factors which may necessitate a reduction in the product’s Working Load Limit (WLL) rating or is cause to remove the product from service and have it quarantined. Therefore, it is recommended that all products be regularly inspected by a competent person to determine their condition as a basis for deciding if the product may continue to be used at the assigned WLL, a reduced WLL, a reduced safety factor or removed from service.
The products shown are, in general, items intended to be used in a tension or pull manner. Caution must be used so that the product is not subjected to side loading that will cause additional and unintended loading.
All hook latches shown are intended to retain loose slings or fittings under slack conditions. They are not intended to be anti-fouling devices. Caution should be used to prevent the latch from supporting any of the load. Periodic inspection of latches must be made to ensure proper operating condition.
Welding of or to load supporting parts or products is not recommended. It is necessary to have knowledge of material, heat treatment and welding procedures before welding of any item is to be considered. We suggest Hercules SLR be consulted for information and proof testing if necessary.
Anyone using rigging equipment is responsible to have training on the usage of the item, as per ASME standards.
All fittings are subject to wear and disfigurement in the form of nicks and gouges, and should be inspected periodically for these conditions.
Any detection of a crack or permanent deformation in a fitting (i.e. hook, shackle, link, etc.) is cause to remove the fitting from service and be quarantined.
Working Load Limit (WLL)
The maximum combined static and dynamic load in pounds or tonnes should be applied to the product in service, even when the product is new, and when the product is uniformly applied in direct tension to the product.
The specific load applied in performance of the proof tests.
A non-destructive load test made to a specific multiple of the rated load of the product.
The load at which the item being tested fails or no longer supports the load.
Any condition of rapid lift, sudden shifting of load or arrest of a falling load.
Nominal Breaking Strength
Published catalogue design strength of a product.
An industry term denoting theoretical reserve capability. Usually computed by dividing the catalogue stated ultimate load by the catalogue stated working load limit and generally expressed as a ratio, for example 5 to 1 (5:1).
The theoretical reserve capability of a product, determined by dividing the breaking strength by the rated working load unless otherwise noted.
All ratings in tons refer to short tons of 2,000 lbs. Ratings in metric tons (tonnes) equal 2,204 lbs.
For more information on Hercules SLR quality, read our news & blog pages:
There is always a safe way to lift every load. For any of your special lifting requirements please contact Hercules SLR.